Ctl NX2700 Bedienungsanleitung Seite 61
- Seite / 103
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
60 • vacon INSTALLATION INSTRUCTIONS
Tel. +358 (0)201 2121 • Fax +358 (0)201 212 205
8
OPT
-
A2
Terminal
Signal
Technical information
21
RO1/1
Relay
output 1
Switching capacity
24VDC/8A
250VAC/8A
125VDC/0.4A
Min.switching load 5V/10mA
22
RO1/2
23
RO1/3
24
RO2/1
Relay output 2
Switching capacity
24VDC/8A
250VAC/8A
125VDC/0.4A
Min.switching load 5V/10mA
25
RO2/2
26
RO2/3
Table 8-4. Control I/O terminal signals on basic relay board OPT-A2
OPT
-
A3
Terminal
Signal
Technical information
21
RO1/1
Relay output 1
Switching capacity
24VDC/8A
250VAC/8A
125VDC/0.4A
Min.switching load 5V/10mA
22
RO1/2
23
RO1/3
25
RO2/1
Relay output 2
Switching capacity
24VDC/8A
250VAC/8A
125VDC/0.4A
Min.switching load 5V/10mA
26
RO2/2
28
TI1+
Thermistor input
29
TI1
–
Table 8-5. Control I/O terminal signals on basic relay board OPT-A3
8.2.2.1 Digital input signal inversions
The active signal level depends on which potential the common inputs CMA and CMB (terminals 11 and 17)
are connected to. The alternatives are either +24V or ground (0 V). See Figure 8-7.
The 24-volt control voltage and the ground for the digital inputs and the common inputs (CMA, CMB) can be
either internal or external.
Figure 8-7. Positive/Negative logic
+24V
+24V
DIN1
DIN2
DIN3
CMA
DIN1
DIN2
DIN3
CMA
nk6_16
Ground
Ground
Positive logic (+24V is the active signal) =
the input is active when the switch is closed
Negative logic (0V is the active signal) =
the input is active when the switch is closed.
Requires setting of jumper X3 to position
‘CMA/CMB isolated from ground’
- START-UP QUICK GUIDE 2
- CONTENTS 3
- VACON NXC USER’S MANUAL 3
- Document code: ud01011.doc 4
- Date: 8.1.2009 4
- Warning symbols 7
- Dangerous voltage 7
- General warning 7
- Hot surface – Risk of burn 7
- EU DECLARATION OF CONFORMITY 9
- 2004/108/EC 9
- Drive modified 10
- 3.1.1 NX type designation 10
- 3.2.9 Door Mounted (D-group) 12
- 18 • vacon TECHNICAL DATA 19
- 4.2 Technical data 19
- TECHNICAL DATA vacon • 19 20
- MOUNTING vacon • 21 22
- Figure 5-2. Lifting the unit 23
- Terminal numbers 25
- MOUNTING vacon • 27 28
- [kw] = P 29
- [kW] x 0,025 29
- 6.2.2 Mains and motor cables 34
- *Recommended 35
- EMC-earthing clamp for 36
- Connect the PE 37
- Installing the cable gland 40
- 6.2.5 Control cable 43
- 6.2.6.1 6-pulse drives 44
- 6.2.6.2 12-pulse drives 45
- 6.2.7.1 6-pulse drives 47
- 6.2.7.2 12-pulse drives 48
- REM-MAN-AUTO 50
- 0-1-Start 50
- 7.1.1 Manual operation (MAN) 50
- 0–1-Start 50
- Continues on the next page 54
- Basic relay board 58
- Control I/O 59
- FAULTSTOP 66
- 9.2.1 Button descriptions 68
- Main menu 69
- Browser buttons 69
- Menu buttons 69
- Menu button right 69
- No editing! 70
- 13.95 Hz 71
- 2 Push the 72
- Min Frequency Min Frequency 73
- Bus/Comm 74
- 9.3.3.2 Keypad reference 75
- Enter button 75
- 9.3.3.3 Keypad direction 75
- 9.3.3.4 Stop button activated 75
- F T1 76
- Fault time data record menu 77
- 9.3.4.3 Real time record 77
- Fault history 11 Output phase 78
- Operation days 78
- PUSH to reset 78
- 9.3.6 System menu (M6) 79
- System menu 79
- CONTROL KEYPAD vacon • 79 80
- Francais 81
- Standard 82
- Multi-step 82
- LoadFactDef 83
- Not in use 85
- Startup wizard Startup wizard 86
- Startup wizard 86
- ChangeEnable 87
- ChangeEnable ChangeDisable 87
- Timeout time 88
- Timeout time Timeout time 88
- Continuous 89
- Temperature 89
- HMI ACK timeout 90
- Not reset Not reset 91
- Not reset 91
- NXFIFF01 92
- A:NXOPTA1 93
- Expander boards 93
- C:NXOPTC1 94
- Parameters 94
- Slave address 94
- 96 • vacon 97
- Real time record 99
- FAULT TRACING vacon • 99 100
- 100 • vacon FAULT TRACING 101
- FAULT TRACING vacon • 101 102
- Vacon distributor: 103
Celestron Dalekohledy uživatelské příručky
Začínající na P
Kommentare zu diesen Handbüchern